The T3 Shotgun Stock fits the Mossberg and Maverick Shotguns and similar in 12 gauge configuration.
Constructed from DuPont Extreme Reinforced Polymer, making it scratch and weatherproof. This TactLite 6-Position adjustable Mil-Spec Stock is compact for transport and carry with length of pull at 13 1/8" to 16 5/8".

The TracLOCK System provides smooth secure stock adjustments, eliminates horizontal and vertical movement of the stock on the buffer tube, eliminates the need for secondary locking mechanisms, has dual-sided QD attachment point, and no snag points.

X Series Recoil Reducing Pistol Grip has built-in X Series recoil absorbing backstrap, sure-grip texture for increased control with its slim ergonomic design.

X2 Recoil Reducing Butt-Pad upgraded to 1 1/4" thick, absorbs recoil impact, reduces muzzle life, and allows you to shoot any load size with no pain transfer to the shooter, eliminating the felt punch of recoil. The Butt-Pad is not affected by chemicals or extreme temperatures.

The adjustable/removable cheekrest has an elongated design to fit all users. It provides 1/2" of vertical adjustment.

The universal mount system securely fastens your tactical stock with no special tools. All supports model mounts and hardware are included in one package.

Features:

TracLOCK System

X Series Recoil Reducing Pistol Grip

X2 Recoil Reducing Butt-Pad

Slot for Tactical Sling Attachment

Adjustable/removable cheekrest

Easy Installation

Universal Mount System

Scratch and Weatherproof

DuPont Extreme Reinforced Polymer

Made in the USA

Fits:

Mossberg 500/535/590/835 12ga & 20ga

Maverick 88 12ga & 20ga

Remington 870/887 12ga

Winchester SXP 12ga year 2020 and older

Most Savage Stevens 320 12ga before 2016,

TriStar Raptor 12ga

Charles Daley 301 Pump-Action Field Shotgun 12ga Shotguns

**Does NOT Fit .410 Gauge Shotguns

T3 Adjustable TactLite Shotgun Stock

Parts List: T3 Stock Sub-assembly, Grip pad, Cheekrest, Right/left Mounts, Grip Adapters (6), Grip Sub-assembl
Grip Adapters: Mossberg 500/535/590/835 12ga & 20ga / Maverick 88 12ga & 20ga. Winchester SXP 12ga, Remington 870/7400 12ga, TriStar Raptor/Cobra 12ga, Remington 887 12ga, Stevens 320 Pre-2016.
Hardware List: Foam Pad, Washer, Lock Washer, Square Nut 8-32, (5) Nut 6-32. Screws: 6-32x3/4”, 6-32x1/4” (4), M8-1.25x50mm, ¼-28x2”, 5/16-18x1½”, 1/4/28x11/4”, 8-32x1/2”, Plastite Screw 6-48x1/2” (2).

 Installation Instructions

       T3 Adapter Installation
Place the appropriate adapter into the pistol grip. Press the adapter into place. Now screw the adapter in place using the 6-48x1/2” Plastite Phillips Flat Head Screws
Grip Installation to Receiver
Place the pistol grip flush against the receiver and using the appropriate bolt and washer tighten the pistol grip to the receiver with the appropriate allen wrench.

      Buffer Tube to Grip Installation
Take the buffer tube and install the 8-32 square nut into the buffer tube bottom slot. Next press the square nut until you can see it centered in the buffer tube.

7.     Buffer Tube to Grip Installation\
Install the buffer tube into the rear of the pistol grip. Flip the shotgun over and make sure the holes of the grip and buffer tube line up. Next using a 9/64 allen head driver and the provided 8-32x3/4” flat head socket cap screw, screw the buffer tube to the pistol grip.

8.     Grip Backstrap Installation
Slide the backstrap onto the pistol grip. Using a Phillips head screwdriver and the provided 6-48x1/2” screw the backstrap to the grip.

Hex Nut to Mount Installation
Begin by placing the (5) 6-32 hex nuts into the slots of the cheekrest mounts until seated properly.

Cheekrest Mount Installation
Begin by attaching the right side cheekrest mount and snap into the pocket until properly seated.
Turn the stock over and attach the left side cheekrest mount and snap into the pocket until seated properly
Using the provided 6-32x3/4” screw thread the screw through the left side cheekrest mount and tighten using the appropriate allen wrench.

3.     Cheekrest Installation
Take the cheekrest and slide onto the cheekrest mounts making sure the holes on the cheekrest line up with the cheekrest mount holes.
Using the provided 6-32.1/4” screw and the appropriate allen wrench, tighten the left side of the cheekrest. Turn the stock over and repeat the process to tighten the right side of the cheekrest.