Marlin 60 75 990 .22 LR Fiberforce Fixed Stock - ATI Outdoors


Marlin+60+75+990+.22+LR+Fiberforce+Fixed+Stock+-+ATI+Outdoors

Processing...
Item #: ATMAR3000

$62.95

In Stock for Immediate Shipping
Qty

Manufacturer MPN:
Advanced Technology MAR3000

UPC: 758152330000
Weight: 11.00 pounds


Product Description

Marlin 60 75 990 .22 LR Fiberforce Stock - ATI Outdoors
Upgrade your Marlin Firearm with a Fiberforce Stock from ATI

For use with open sights or scope. Manufactured in the USA of DuPont extreme temperature glass reinforced polymer. Comes complete with upper ventilated forearm and handguard, Sure-Grip textured pad for improved grip, built-in cheek rest with 3M Soft Touch cheekrest pad for improved comfort when shooting, two sling swivel studs and dowel sling mount. Weighs only 26 oz. Easy drop-in installation. Mfg. limited lifetime warranty. 

Fits Marlin Model 60, 75, 990, 99M1 and similar including both Tube or Detachable Mag Models .22LR. Fits Glenfield Model 75 semi-auto tube feed. 
Will not fit the Marlin 795.
Some Minor Modification may be Required. For proper fit, you may need to remove some material to fit on various Marlin Models.

Marlin Fiberforce Stock Installation Instructions
Step 1: Begin by using a flathead screwdriver and unscrewing the (2) take-down screws from the underside of your Marlin.
Step 2: Next, lift the barreled action out of the old stock.
Step 3: Remove the trigger group retaining screws.
Note: Secure the flange nut while removing the screw. Lift the trigger group from the old stock. The flange nut must be inverted for use in the new stock
Step 4: For clip-fed rifles, remove the oval recessed area in the bottom of the stock, just forward of the trigger assembly opening. Stock material is easily removed with most common woodworking tools, drills, and files.
Step 5: Install the trigger assembly into the ATI Fiberforce stock, (the snug fit is intentional), and reinstall the flange nut and trigger retaining screw that was removed in Step 3.
Step 6: Next, install the upper handguard onto the barrel.
Step 7: With the handguard in place on the barreled action, align the front tabs of the stock to the front slot of the handguard. Continue to match tabs and slots until the top handguard sets with the stock and barrel assembly.
Step 8: Install and tighten the take-down screw that was removed in Step 1 using a flathead screwdriver.
Step 9: Install the front portion of the grip by sliding into place and then snapping the grip onto the Fiberforce stock handle.
Step 10: Install the cone-shaped #8/32 x 2” screw through the trigger assembly, because this screw passes through the hole in the rear of the trigger assembly, it may be necessary to loosen the front screw of the trigger assembly. Tighten with a phillips head screwdriver until snug.

B: Adhesive Pad Installation
Step 1: Begin by using the supplied alcohol swab to clean the cheek rest area on both sides of the stock.
Step 2: Wait 30 minutes until the alcohol is dried. Remove the backing from the adhesive pad and align the pad to the stock.
Step 3: Continue to align the pad to the stock. Keep slight tension on the pad and bring the pad around the surface of the stock.
Step 4: Use your thumb to remove any air bubbles in the pad and to firmly press and secure the adhesive pad onto the cheek rest.

C: Soft Touch Cheek Rest Pad Installation
Step 1: Begin by using the supplied alcohol swab to clean the cheek rest area on both sides of the stock.
Step 2: Wait 30 minutes until the alcohol is dried. Remove the backing from the adhesive pad and align the pad to the stock.
Step 3: Continue to align the pad to the stock. Keep slight tension on the pad and bring the pad around the surface of the stock.
Step 4: Use your thumb to remove any air bubbles in the pad and to firmly press and secure the adhesive pad onto the cheek rest.


Related Categories That You May Also Be Interested In:
 ATI Advanced Technology |  Shotgun and Hunting Stocks |
•••••