The TactLite Six-Position Adjustable SKS Stock is made from DuPont Extreme Temperature Glass Reinforced Polymer, making it scratch and weatherproof. The stock side-folds to the Left of the receiver and can be fired from folded position. The stock has additional ventilation in forend and top cover, slot for tactical sling attachment, two sling swivel studs. All mounting hardware is included.

The TracLOCK System provides smooth secure stock adjustments, eliminates horizontal and vertical movement of the stock on the buffer tube, eliminates the need for secondary locking mechanisms, has dual-sided QD attachment point, and no snag points.

The adjustable/removable cheekrest has an elongated design to fit all users. It provides 1/2" of adjustment.

X Series Thin Recoil Pad is non-slip and removable. X1 Style Pistol Grip has sure-grip texture for more control, absorbs recoil impact, reduces the challenge to reacquire the target by minimizing Muzzle Lift. Due to the design, it is not affected by chemicals or extreme temperatures.

Four Forward Picatinny Rail Locations: one 4" Picatinny Rail, three 2" Picatinny Rails, one 2" Picatinny Rails, one 2" Swivel Stud picatinny Rail, and blank covers for unused rail locations.

Features:

TactLite 6-Position Adjustable Stock

TracLOCK System

Removable/Adjustable Cheekrest System

X Series Thin Recoil Pad

X1 Style Pistol Grip

Four Forward Picatinny Rail Locations

Additional ventilation in forend and top cover

Slot for tactical sling attachment

Two sling swivel studs

Made in the USA

Fits: SKS Rifles - Minor modification may be required in some cases. Blade Bayonet must be removed.

Notes: SKS Scope Mount NOT included/Sold Separately

Sling Swivel Studs Accepts any Standard Sling Swivel (not included)

SEC922R: ATI products are manufactured in the USA and count towards compliance parts. Contact your local gun shops or shooting ranges for this and other compliance issues.

Strikeforce SKS Stock
Parts List: Stock Sub-assembly, Stock body, Top cover, Pistol Grip, 4” Bottom rail, Side/bottom rail (4), blank inserts (4).
Hardware List: Spring, Sling Stud 10-32x4/16, Sling Stud 3/8” Course, Nut 10-32, Nut 6-32 (8).
Screws: #14x1 1/4”, 6-19x3/4”, 6-19x1/2” (2), 6-32x3/8” (8).

Installation Instructions:

1.     Trigger Assembly Removal
To remove the trigger assembly, begin by inserting a pin punch or phillips head screwdriver into the spring latch catch at the rear of the trigger guard and pressing inward firmly until the spring latch releases. The trigger assembly will no spring out and can be removed from the stock by pulling outward on the rear of the receiver.

2.     Barreled Action Removal
To remove the barreled action from the stock body, pull outward and towards the rear.

3.     Gas Tube Assembly Removal
Using a punch or small screwdriver, raise the lever on the right side of the rear sight base. The dimple on the lever should stop at the end of the curved track on the right side of the rear sight base. With the lever in this position, you can now lift upward at the rear of the gas tube and out of the firearm. Next, remove the gas piston from the assembly by tipping it upside down and letting it slide out. There is a small rivet running though the rear handguard in the gas tube assembly. The rivet has two ends, the head, and the shaft end. Be sure to punch out the shaft end and remove the rivet using a 1/16” punch.

4.     Top Sling Stud Installation
To install the top sling stud, locate the hole on the top of the stock near the folding button. Using an adjustable wrench, tighten the sling stud until seated.

5.     Blank Insert (Optional) Installation
If you choose to install the 4 blank inserts into the stock body, you will take one insert and install into the side of the stock body making sure the tabs line up into the stock body until flush. You will repeat this same process for the left side, and both bottom slots.

6.     Picatinny Rail (Optional) Installation
If you choose to install the bottom picatinny rail with the sling stud, begin by installing the 10-32 hex nut into the pocket on the bottom of the picatinny rail. Next, while holding your finger over the 10-32 hex nut, thread the sling stud into the rail until it is seated into the hex nut.

Next, install (2) 6-32 hex nuts into the pockets on the bottom of the inside stock body. Align the bottom rail into place and while holding a finger over the hex nuts, fasten the rail using (2) 6-32x3/8” machine screws and a phillips head screwdriver.

To install the 4” bottom rail, begin by removing the 2” rail, making sure to keep the hex nuts installed. Next, locate the remaining 2 pockets on the inside of the stock body and insert (2) 6-32 hex nuts into the pockets. Align the bottom rail into place and while holding a finger over the hex nuts use a phillips head screwdriver to fasten (4) 6-32x3/8 machine screws to the picatinny rail.

To install the side rails, begin by locating the existing pockets on the inside of the stock body and insert (2) 6-32 hex nuts into the pockets. Align the side rail into place and while holding a finger over the hex nuts use a phillips head screwdriver to fasten (2) 6-32x3/8 machine screws to the picatinny rail.

7.     Magazine Installation
Begin by turning the barreled action over and installing the magazine, making sure to mate the magazine to the slot on the bottom of the rear sight base until seated.

8.     Barreled Action Installation
Next, install the barreled action into the stock body, making sure the stock is as far forward on the action as it will go and slide into place. You will also want to make sure the front of the stock body seats onto the band of the front of the barreled action.

9.     Trigger Installation
To install the trigger assembly, insert the front of assembly into the stock making sure the cross pins go to locator lugs on the bottom of the receiver. Tap the trigger guard forward and firmly push down on trigger assembly until it locks into place.

1.  Gas Tube Cover Installation|
To install the gas tube cover onto the gas tube, begin by placing the cover onto the gas tube and sliding into place until the front of the handguard is seated.

Note: Because the SKS is a mil surplus firearm, the band may be disformed from previous re-manufacturing. Because of this you may need to re-form the bad to help with seating of ATI gas tube cover.

Next, install the rear sheet metal cover onto the gas tube until seated. Note: the sheet metal cover may not always sit flush against the handguard. Place the rivet into the hole in the sheet metal cover and lightly tap the rivet until seated. Note: Because the SKS is a mil surplus firearm, the band may be disformed from previous re-manufacturing. Because of this you may need to re-form the bad to help with seating of ATI gas tube cover.

11.  Gas Tube Installation
To install the gas tube, begin by inserting the front of the gas tube assembly into the proper location until seated.
Next, making sure the lever on the rear sight base is raised, insert the rear of the gas tube assembly, and push down until seated. Make sure the lever is all the way down and locked into place.

12.  Pistol Grip Installation
Due to the many variations of the SKS a trigger group spring is required. Insert the trigger group spring into the pilot hole of the grip. Installation of the spring will provide a tight fit between the receiver, trigger assembly, and Strikeforce Stock.
To install the pistol grip, begin by removing the backstrap from the grip and seating the grip housing onto the stock body. Next, using the 6-19x3/4” screw and a phillips head screwdriver tighten the grip to the stock. Slide the backstrap onto the grip housing until seated and using the (2) 6-19x1/2” screws tighten the backstrap until snug.

13.  Tube to Grip Assembly Installation
|With the knuckle in the folded position, slide the buffer tube into the knuckle. Using a phillips head screwdriver and the provided 14x1 ¼” phillips head screw tighten the tube through the back of the knuckle.

 

TactLite Adjustable Cheekrest Kit
Parts List: Cheekrest, right/left mounts
Hardware list: 6-32x3/4” and (4) 6-32x1/4” screw, Nut 6-32 (5)

Installation:

1.     Hex Nut to Mount Installation
Begin by placing the (5) 6-32 hex nuts into the slots of the cheekrest mounts until seated properly.

2.     Cheekrest Mount Installation
Begin by attaching the right side cheekrest mount and snap into the pocket until properly seated.
Turn the stock over and attach the left side cheekrest mount and snap into the pocket until seated properly
Using the provided 6-32x3/4” screw thread the screw through the left side cheekrest mount and tighten using the appropriate allen wrench.

3.     Cheekrest Installation
Take the cheekrest and slide onto the cheekrest mounts making sure the holes on the cheekrest line up with the cheekrest mount holes.
Using the provided 6-32.1/4” screw and the appropriate allen wrench, tighten the left side of the cheekrest. Turn the stock over and repeat the process to tighten the right side of the cheekrest.