Ruger 10/22 Strikeforce Adjustable Folding Stock - ATI Outdoors


Ruger+10%2F22+Strikeforce+Adjustable+Folding+Stock+-+ATI+Outdoors

Processing...
Item #: ATB2101216

$113.95

In Stock for Immediate Shipping
Qty

Manufacturer MPN:
Advanced Technology B.2.10.1216

UPC: 758152910899
Weight: 9.00 pounds
Check Restrictions


Product Description

Ruger 10/22 Strikeforce Adjustable Six Position Side-Folding Stock - ATI 
The ultimate 10/22 six position collapsible/side folding stock for the perfect fit.
Weapon can be fired from the folded position. 

Includes removable adjustable cheekrest system, additional ventilation in forend and top cover, slot for tactical sling attachment, drop tube adaptor for use with iron sites, two sling swivel studs, one 4" Picatinny top rail, three 2" Picatinny rails, one 2" swivel stud Picatinny rail and blank covers for when rails are not in use. All mounting hardware included.
Features a Scorpion Razorback Recoil Pad included to reduce the challenge to reacquire the target by minimizing the muzzle lift. Non-Slip, Removable.
Limited Lifetime Warranty. Made in USA

Fits Most Ruger 10/22. Will not fit Bull Barrels or 10/22 Charger.

INSTALLATION INSTRUCTIONS for Ruger 10/22 Strikeforce Stock

1: Blank Insert (Optional) Installation
If you choose to install the (4) blank inserts into the stock body you will take one insert and install into the side of the stock body making sure the tabs line up into the stock body until flush. You will repeat this same process for the left side and both slots on the bottom.

2: Picatinny Rail (Optional) Installation
If you choose to install the bottom picatinny rail with the sling stud begin by installing the 10-32 hex nut into the pocket on the bottom of the picatinny rail. Next, while holding your finger over the 10-32 hex nut (#6), thread the sling stud into the rail until it is seated into the hex nut.
Next, install (2) 6-32 hex nuts (#5) into the pockets on the bottom of the inside stock body. Align the bottom rail into place and while holding a finger over the hex nuts, fasten the rail using (2) 6-32 x 3/8” machine screws (#4) and phillips head screwdriver.
To install the 4” bottom rail you would first need to remove the 2” rail, making sure to keep the hex nuts installed. Next, begin by locating the remaining (2) pockets on the inside of the stock body and insert (2) 6-32 hex nuts (35) into the pockets. Align the bottom rail into place and while holding a finger over the hex nuts use a phillips head screwdriver to fasten the (4) 6-32 x 3/8 machine screws (#4) to the picatinny rail.

To install the side rails, begin by locating the existing pockets on the inside of the stock body and insert (2) 6-32 hex nuts (#5) into the pockets. Align the side rail into place and while holding a finger over the hex nuts use a phillips head screwdriver to fasten the (2) 6-32 x 3/8 machine screws (#4) to the picatinny rail.

3: Stock Assembly to Stock Body Installation
To install the tube/stock to the stock body, you will need to make sure the stock is in the folded position. Begin by pressing together on the pin cap and under the pivot housing until folded to the side. Next, install the tube into the knuckle. Using a phillips head screwdriver and the provided 14 x 1 ¼” phillips head screw (#1), tighten the tube through the back of the knuckle.

4: Barreled Action Installation
To install the barreled action, align the barrel to the front of the stock and bring the receiver down towards the rear of the stock and firmly secure the action in place.

5: Take Down Screw Installation
Turn the stock over and locate the take down screw hole and using the original takedown screw and appropriate driver, tighten until seated.

6: Top Cover Installation
Align the top cover plate from the front and bring the cover down until seated. Using a 7/64 allen key (#9) and the provided 6-32 x ¾” allen head screw (#2) tighten the rear of the cover plate to the stock body. Using the provided 7/64 allen key (#9) and the provided 6-32 x ½” allen head screw (#3) tighten the front cover of the cover plate to the stock body.
Note: Do not overtighten screw as this may pull the brass insert out of the bottom stock body.

7: Top Sling Stud Installation
To install the top sling stud (#8), locate the hole on the top of the stock near the folding button. Using an adjustable wrench tighten the sling stud until seated.

TacLite Adjustable Cheekrest Kit Installation
1: Hex Nut to Mount Installation
Begin by placing the (5) 6-32 hex nuts into the slots of the cheekrest mounts until seated.

2: Cheekrest Mount Installation
Begin by attaching the right side cheekrest mount and snap into the pocket until seated.
Turn the stock over and attach the left side cheekrest mount and snap into the pocket until seated.
Using the provided 6-32 x ¾” screw (1) thread the screw through the left side cheekrest mount and tighten using the appropriate allen wrench.

3: Cheekrest Installation
Take the cheekrest and slide onto the cheekrest mounts making sure the holes on the cheekrest line up with the cheekrest mount holes.
Using the provided 6-32 x ¼” screws (2) and the appropriate allen wrench, tighten the left side of the cheekrest. Turn the stock over and repeat the process to tighten the right side of the cheekrest.

 

 

 




Related Categories That You May Also Be Interested In:
 ATI Advanced Technology |  Ruger 10/22 Accessories |  Tactical Rifle Stocks |
•••••